Infocus IN1112A Specifikace

9Adjusting the imageIf necessary, adjust the height of the projector by pressing the elevator foot release button to extend the foot.If necessary, rot

10Video device connectionsNo video cables are provided with the projector. You can order cables from InFocus or provide your own.Composite video conne

11Shutting down the projectorThe projector automatically displays a black screen after no active source is detected for 30 minutes. This black screen

Problem Solution ResultNo start up screen®multimediaPlug power cord into the projector and press the power buttonStartupScreenCorrect imageOnly start

13Problem Solution ResultNo computer image, just the words “Signal out of range”ASignal out ofthe rangePress the Auto Image button on the keypad. Adju

14Image fuzzy or croppedAAChange the computer's "Resolution" setting to match the projector's resolution (Windows 7: Control Panel

15Image not square Adjust Keystone on keypad Square imageImage not sharpABAdjust Sharpness in the Basic menu Correct imageABImage does not fit 4:3 or

16Image reversed left to rightATurn off Rear Project in Advanced > Setup > Image Position menuCorrect imageABProjected colors don’t match sourc

17Lamp won’t turn on, Temperature light is onTemperature lightMake sure vents aren’t blocked, turn off the projector and allow it to cool for one minu

18Still need assistance?If you need assistance, visit our website at www.infocus.com/service or call us. Check out our HOW TO section there for additi

1Declaration of ConformityManufacturer: InFocus Corporation 13190 SW 68th Parkway, Portland, Oregon 97223-8368 USA We declare under our sole responsib

19Using the remote controlThe remote uses two (2) AA batteries (batteries not included). They are easily installed by removing the cover from the remo

20Using the audioUsing the projector’s speakerTo use the projector's speaker, connect the audio source to the projector's Audio In connector

21Using the keypad buttonsmenu navigation buttonsMost buttons are described in detail in other sections, but here is an overview of their functions:Po

22Optimizing computer imagesAfter your computer is connected properly and the computer’s image is on the screen, you can optimize the image using the

23Optimizing video imagesAfter your video device is connected properly and the image is on the screen, you can optimize the image using the onscreen m

24Using the menusTo open the menus, press the Menu button on the keypad or remote. (The menu automatically closes after 60 seconds if no buttons are p

25Basic menuTo change the following menu settings (or enter the Advanced menu), highlight the desired menu option and press the Select or right arrow

26Advanced > Image menu3D Control:• 3D: toggles between on and off. Turn it on to display the image in 3D.• 3D Sync Invert: toggles between on and

27Advanced > Setup menuAudio Setup:• Power Sounds: controls whether the projector makes a sound when powered on and off. • Vol u m e: adjusts the

28Keypad/Remote:• Blank Key: selects what to display when the Blank Key on the remote is pressed: your custom snapshot, a solid color screen (blue, bl

2Table of ContentsIntroduction 4Positioning the projector 6Connecting a computer source 7VESA connection 7HDMI connection 7Power connection 7Optional

29Pin Settings: • Change PIN:To enter the PIN at projector startup:Power up the projector. The "Enter PIN" dialog box appears after the star

30Source:• Power-up Source: determines which source the projector checks first for active video during power-up.• Search Screen: allows you to display

31Advanced > Status/Service menuSource Info: a read-only display of current source settings.Projector Info: a read-only display of current projecto

32Multimedia EZ Suite Menu When a USB source is inserted into the projector (USB-A or USB-B), press the Source key and use the arrow keys to highlight

33To display a control bar to control the photos:1 Press the Menu key on the remote or keypad.2 Use the left and right arrows to highlight a control b

Table 4: Compatible Image TypesImage Type Sub Type Encode Type Max PixelsJPEG, JPGBaselineYUV400 No LimitYUV420 No LimitYUV422 No LimitYUV440 No Limit

358To open the video control bar while the movie is playing, press the Menu key. PauseRewindPlayFast ForwardTo pause/play the audiovisual file: Press

Table 11: Compatible Video TypesFile Type Video Resolution Bit Rate Frame Rate Audio Code CommentAV I , M K VXVID, MPEG4, H.264, M-JPEG, WMV31080P 20

37Listening to Audio Files1To listen to audio files, navigate to EZ Media and press the right arrow or the Select key.2 Using the up and down arrows,

38• To go to the next audio file: Press the right arrow key twice within one second. 9 Press the Menu key to close the audio file and return to the

3Important Operating Considerations for Safety• Place the projector in a horizontal position no greater than 15 degrees off axis.• Locate the projecto

397Press the right arrow or the Select key to open the file.8 To go to the next page, press the down arrow key.9 To go to the previous page, press the

40EZ DisplayEZ Display allows you to project your files from your PC, MAC, Android or iOS device wirelessly with optional adapters SP-WiFiUSB or SP-Wi

41WiFi can be configured with your browser.Multiple users connected via the EZ WiFi/LAN application can be controlled with your browser. Table 17: EZ

42Settings1 To configure the System, Video, Photo, Audio or WiFi settings, navigate to Settings and press the right arrow or the Select key.2 Using th

43Video SubmenuTo adjust the Video Display Ratio: Highlight Display Ratio and use the left and right arrow keys to select the desired mode. Press the

44Audio SubmenuTo adjust the Audio Repeat mode: Highlight Repeat mode and use the left and right arrow keys to select the desired mode. Press the Sele

45Auto: Auto channel switching is not supported.3 Save the configuration by highlighting the checkmark and press the Select key. 4 If you want to exit

46EZ Remote Allows you to control the projector from your Android or iOS device. Note: A wireless connection must be established to operate this featu

47MaintenanceCleaning the lens1 Apply a non-abrasive camera lens cleaner to a soft, dry cloth.• Avoid using an excessive amount of cleaner, and don’t

48Replacing the projection lampThe lamp hours used timer in the Projector Info menu counts the number of hours the lamp has been in use. Twenty hours

4IntroductionYour new digital projector is simple to connect, easy to use, and straightforward to maintain. The IN1110a has native XGA 1024x768 resolu

491Turn off the projector and unplug the power cord.2 Wait 60 minutes to allow the projector to cool thoroughly.3 Turn the projector upside down on a

50INDEXNumerics3D Control3D 263D Sync Invert 26AAdvanced > Image > 3D Control Menu 26BBasic menu 25Aspect Ratio 25Auto Image 25Brightness 25Cont

51MMaintaining the projector 47Menu usage 24OOptimizing images 22Optimizing video 23Overscan 26, 27, 28, 29, 30PPC 26Force Wide 26PC Screen Saver 26Ph

52Volume button 20WWarranty 18ZZoom 9

5Connector panelThe projector provides the following connectors:• Mini USB Type B: Used for advancing slides, Display over USB, saving files to intern

6Positioning the projectorTo determine where to position the projector, consider the size and shape of your screen, the location of your power outlets

7Connecting a computer sourceVESA connectionConnect one end of the provided computer cable to the Computer connector on the projector and the other to

8Displaying an imageTouch the Power button.The Power indicator blinks green and the fans start to run. When the lamp comes on, the start up screen dis