Infocus ScreenPlay 7210 Uživatelský manuál

User’s GuideInFocus CorporationIn the Americas:27700B SW Parkway Avenue Wilsonville, Oregon 97070-92151-800-294-6400 •503-685-8888Fax: 503-685-8887htt

9Displaying a video imageRemove the lens cap. Press the Power button on the top of the projector.The projector chimes if the chime feature is enabled

10Adjust the zoom or focus rings by rotating them until the desired image size and sharpness are produced.If the image is not square, adjust the keyst

11Connecting a computerConnect either a VESA cable or M1 cable into the appropriate connector on the projector. Connect the other end to the video por

12Shutting down the projectorPower SaveThe projector has a Power Save feature in the System menu that automati-cally turns the lamp off after no signa

13Problem Solution ResultNo startup screenPlug power cable in and remove lens cappress Power buttonCorrect imageImage not centered on screenMove proje

14Image not squareAdjust keystone on keypad or Keystone menuSquare imageImage does not fit 16:9 screenChange aspect ratio to 16:9 in Picture>Aspect

151. Projected colors don’t match source2. Colors are washed out or too deep3. Image from component source appears greenish1. Adjust color, tint, colo

16Video image “torn” and fragmentedChange Video Standard in Picture>Advanced menuCorrect imageLamp won’t turn on, LED blinking red (page 12)Make su

17Computer-specific troubleshootingOnly startup screen appearsPress the Source button Activate laptop’s external portComputer image projectedNo comput

18Image fuzzy or cropped Set your computer’s display resolution to the native resolution of the projector (Start>Settings>Control Panel>Displ

1ENGLISHDeclaration of ConformityManufacturer: InFocus Corporation, 27700B SW Parkway Ave. Wilsonville, Oregon 97070 USAEuropean Office: Strawinskylaa

19Still having problems?If you need assistance, visit our website or call us. See the inside of the back cover for support contact information. This p

20Using the keypad buttonsMost buttons are described in detail in other sections, but here is an over-view of their functions:Power–turns the projecto

21Using the remote controlThe remote uses two (2) provided AAA batteries. They are easily installed by sliding the cover off the remote’s back, aligni

22Optimizing video imagesAfter the video device is connected properly and the image is on the screen, you can optimize the image using the onscreen me

23Using the menusTo open the menus, press the menu button on the keypad or remote. (The menus automatically close after 60 seconds if no buttons are p

24Picture menuTo adjust the following five settings, highlight the setting, press Select, use the up and down arrows to adjust the values, then press

2516:9: the default is 16:9, which preserves the 16:9 aspect ratio and is designed to be used with content that is Enhanced for Widescreen TVs. 4:3: r

26Presets: This allows you to customize settings and save the settings to be restored later. To restore the factory default settings, choose Factory R

27Advanced settingsThe following 4 options are for computer or HDTV sources only. Phase: adjusts the phase of the video signal’s digital conversion.Tr

28Color Space: This option applies to computer and HDTV sources (it won’t appear in the menu for video sources). It allows you to select a color space

2Table of ContentsIntroduction 4Positioning the projector 6Video connections 7Connecting a video device 8Displaying a video image 9Connecting a co

29Settings menuSources: allows you to assign a particular input to a specific source key on the remote and enables or disables Autosource. When Autoso

30Tr a n s l uc e nt O S D : makes the menus translucent. This prevents the image from being completely covered by the menus while you are making ima

31Service: to use these features, highlight them and press Select.Factory Reset: restores all settings (except Lamp Hours) to their default after disp

32Replacing the projection lampThe lamp hour timer in the About menu counts the number of hours the lamp has been in use. Twenty hours before the lamp

33WARNINGS: • To avoid burns, allow the projector to cool for at least 60 minutes before you replace the lamp.• Do not drop the lamp module. The glass

34AppendixRed LED behavior and projector errorsIf the projector is not functioning properly and the red LED is blinking, con-sult Ta bl e 2 to deter

35Source compatibilityTable 5: Source CompatibilityVideo Component and RGB HDTV (720p, 1035i, 1080p, 1080p-24Hz)DVI/HDCP for digital video and encrypt

36Projector dimensions for ceiling mount installations11.3”288.1mm2.6”64.9mm2.3”57.8mm2.1”53.7mm12.3”312.7mmtotal length with optional cable cover: 16

37RS-232 terminal specificationsCommunication configurationTo control the projector from an LCD control panel, connect an RS-232 cable to the serial c

38Supported commandsFunction Command Range DefaultAspect Ratio ARZ 0-40 = Native1 = 16:92 = 4:33 = Letterbox4 = Natural Wide1Auto Chime Enable ACE 0-1

3Important Operating Considerations• Place the projector in a horizontal position no greater than 15 degrees off axis. See “Positioning the projector”

39Language LAN 0-110 = English1 = French2 = German3 = Spanish4 = Chinese Tradi-tional5 = Japanese6 = Korean7 = Portuguese8 = Russian9 = Norwegian10 =

40Numerics12v triggers 5, 3516x9 5, 14, 22, 24, 254x3 254x3 aspect trigger 5AADC Calibration 31adjusting image 10, 24Advanced menu 27Aspect Ratio 24Au

41image does not fit screen 14image edges distorted 14image not centered 13image not square 14image offset 6image reversed 15image size matrix 34image

42remote control 21replacing the lamp 32resetting lamp timer 33saving settings 26security lock 33setting up 6shutting down 12troubleshooting 12RRear 2

43Limited WarrantySubject to the Limitations, Exclusions and Disclaimers hereof, InFocus Cor-poration (“InFocus”) warrants that the Projector, Lamps a

44Limited Warranty PeriodThe Limited Warranty periods hereof commence on the date of purchase by the end-user customer. These Limited Warranty provisi

4IntroductionCongratulations and thank you for your excellent choice of a superior digi-tal image projection device. Your new ScreenPlay™ 7210 project

5Connector PanelThe projector provides eight discreet video connectors: • two red-green-blue RCA (SD/ED/HD component)• two S-video•one composite RCA•

6Positioning the projectorThere are a number of factors to consider when determining where to set up the projector, including the size and shape of yo

7Video connectionsYou can connect VCRs, DVD players, camcorders, digital cameras, video games, HDTV receivers, and TV tuners to the projector. (You ca

8Connecting a video device If your video device has more than one output, select the highest quality one. DVI video has the best quality, followed by